You might be unlucky and crash owing to some harsh or unforeseeable topography. If you find yourself unprepared, this might prevent you from moving forward. Here we have some bike maintenance hacks to get you back on track if you ever find yourself with bicycle troubles on the side of the road.
1. Bent Derailleur
When you crash your bicycle, you can get a bent derailleur. You will have to straighten the derailleur because it won’t work unless you straighten it first. If the bulk of the bend is in the frame, then it’s relatively easy to straighten it. You should try removing the rear wheel and then extract its quick release skewer. Unscrew the derailleur to take it off the frame. Now thread the end of the axle into the frame. You will have to thread it in fully and then use wheel to coax the bent piece of metal straight and then repair it. Finally reinstall the derailleur and wheel, and that should do the job.
2. Broken shift cable
If you break your shift cable in your ride, do not panic. There are different remedies, depending upon where the cable has broken. If the cable has broken at the top or in the middle, pull the cable while you pedal, using your hand to get the chain into the appropriate gear. Now, unscrew the water bottle screw and place the cable underneath it and tighten the screw underneath to hold the cable. If there is not enough cable, then tighten the limit screw on the derailleur to make it stay in easy gear anyway. You can also use a stone or stick inside the derailleur to hold it in the required gear.
3. Flat repair
What if all of a sudden, you get a flat tire on the road? If there is grass nearby, stuff the tire with grass and then reattach it to the bike. You can also try removing the tire, locating the hole in the tube and then trapping the part that has a hole under the edge of the tire.
4. Wheel fix
If you ever have a crash, your wheel might take on a bizarre indicating that the rim has been damaged beyond repair. Remove the wheel, hold and roll it to find the biggest bend in it. Now after locating the damaged area, place it so that it’s at 12 o’clock position such that your right hand is at 9 o’clock and your left is at 3 o’clock. Now raise the wheel and smack it down on the ground. It should get the wheel straight; otherwise repeat the step and then find another bend and do the same. This can get the wheel straight enough to get you to your destination.
5. Chain maintenance
The bicycle chain is one of the most efficient energy transfer mechanisms. The parts of the chain are constantly moving against each other, which causes the chain to wear down, making it look elongated. Once the wear progresses beyond a certain point, it makes moving to different gears less smooth, and also causes changes to the gear’s teeth, making it impossible to replace the chain without also replacing the gears. So, it’s advised to lubricate and clean the chain regularly. Spray-on lubricants should be used before every ride and after every wet ride. Apply lube at one point and then rotate the crank so that coat of lube gets spread in the entire chain. Then, stop applying the lube, but continue to rotate the crank to allow the lube to reach every portion of the chain.
6. Inner tube replacement in case of puncture
First, remove the valve of the inner tube and then pull inner tube completely out of the tire. Look on the outside and use your fingers to find the point of the puncture. To install new inner tube, remove the dust cap, lock the ring on new inner tube and then use pump to inflate the inner tube so that it holds its shape. Then, insert the inner tube valve into the valve hole and screw on the lock ring. Finally, place the rest of the inner tube inside the tire.
7. Brakes
Though it is true that brake pads often last for miles, it is also possible to wear through a new set in a single ride if conditions are not good. If you hear very loud scraping when you apply the brakes there is a fair chance that something has lodged into your brake pad. Flip open the brakes or remove the wheel and pick out the source of the issue. It’s advised to not touch disc-brake pads with your fingers.
8. Squeaks and squeals
If your bike starts to make creaking noises, it’s time to look it over. A creaky noise can be attributed to a loose spindle. To undo it, remove the crank bolts, lubricate threads, and reinstall and then tighten everything using a torque wrench. For the saddle, a few drops of oil on the rail where it connects to the saddle will do. To silence the squealing rear-derailleur pulley wheels, light lubricant should be used.
9. Shakes, rattles and rolls
The headset, hubs and cranks should be checked periodically. Squeeze the front brake and rock the bike back and forth to check the headset. Pull the wheel and crank it side to side to check the wheel and crank bearings. Check the tightness of the crank bolt using a torque wrench.
10. Gear tuning
To tune your gears, start by putting your bike into its top gear, and then turn the pedals till the chain goes into the smallest cog. Unscrew the bolt by securing the cables to derailleur and move cable onto the appropriate cogs. Ensure that the chain sits comfortably on both lowest and highest cogs and refit the gear cable. Featured photo credit: Pixabay via pixabay.com